All prices in USD. Welcome to our store! If you have any questions, please use chat for assistance.
All prices in USD. Welcome to our store! If you have any questions, please use chat for assistance.
Cart 0

Fast & Furious Encoder Board Cheat Sheet

There are lots of cool hidden options and features on our Encoder Boards for Arcade1up Fast & Furious mod kits. In fact, so many options, that it can be hard to remember them all.

So, here is a quick guide to the various options, how they work and how to activate them. The buttons referenced below match the suggested labelling we provide in our kit instructions or available on FFencoder.buystuffarcades.com

START UP options.

These options ONLY work when first powering on the encoder board. The encoder will quickly check for these key combos when turning on and not again until re-powered. When using our Gaming Box, turning on the power switch will activate the encoder board. However, when using PC builds, remember that the encoder is powered via USB from your PC, so you will need to disconnect that USB to re-power the encoder board.

CALIBRATE the Pedals: HOLD A & B with the Pedals Down

The rumble will activate twice to let you know to let go of the pedals. If you hold them too long, simple reboot the machine and it will correct itself.

It is essential to calibrate your pedals because every set is slightly different. Some games will work and some will not with pedals that aren't calibrated. This should only need to be done once, but if you are having trouble starting games or getting them to work properly, Calibrate Your Pedals.

SWITCH R Stick and R Trigger Modes: HOLD Y & X

The rumble will activate once to let you know you are in Right Stick mode and twice to let you know you are in Right Trigger mode. 

Right Stick mode is used with our Gaming Box. Most other PC or Console builds will use Right Trigger mode. You can switch back and forth as often as needed.

SWITCH Pedal Inverted Modes: HOLD Y & B

The rumble will activate once to let you know you are in Normal Pedal mode and twice to let you know you are in Inverted Pedal mode.

Inverted Pedal mode is used when mounting pedals upside down, so that the brake becomes the gas and vice versa. 

DISABLE Pedals: HOLD Y & A

The rumble will activate once to let you know pedals are active and twice to let you know pedals are disabled.

Disabling pedals is mainly used if you do not have pedals connected so that they don't create input interference. Generally, this is most common with the StarWars Yoke build when not using pedals and strictly playing the flying games.

Calibrate X Axis: HOLD A and follow below:

It will not normally be necessary to calibrate the X axis (steering wheel), but could required in some unusual circumstance.

If you hold A when starting up for 1 second, the Rumble motor will activate and you need to turn the Wheel fully to the LEFT and hold for 3 seconds. 

DURING PLAY options.

These options work at any time when the Gaming Box or PC is booted up with the Encoder Board connected. That includes in-game or in the menus. Keep in mind that he hot keys below will still cause interaction in the game, although will often trigger the pause function.

Sensitivity Adjustment: HOLD Y & B and move Shifter Up or Down

The rumble will activate with each adjustment and a longer rumble when max or min is hit. 

If the game you are playing is too "twitchy" and you would like to be able to move the wheel further to the right and left, then decrease the Sensitivity with Shifter Up. If you want to be able to turn the wheel less to achieve your turns, then increase the Sensitivity with Shifter Down.

Deadzone Adjustment: HOLD Y & X and move Shifter Up or Down

The rumble will activate with each adjustment and a longer rumble when max or min is hit. 

Deadzone is not the same as Sensitivity. Deadzone refers to a "dead" area at the middle of the wheel where the vehicle doesn't respond. To decrease that Deadzone so that the vehicle responds more quickly to the movement of the wheel, then hold Start and move the Shifter Up. To increase the deadzone, hit the Shifter Down.

There are some games that are virtually unplayable unless you decrease the deadzone because otherwise you can not make accurate micro adjustments.

Rumble Adjustment: HOLD Y & A and move Shifter Up or Down

The rumble will activate with each adjustment and a longer rumble when max or min is hit. 

Move the Shifter Up to increase the Rumble power and the Shifter Down to decrease Rumble, including all the way off.